-
1 инденторная нагрузка
-
2 нагрузка на индентор
-
3 инденторная нагрузка
Engineering: indentation loadУниверсальный русско-английский словарь > инденторная нагрузка
-
4 нагрузка на индентор
Makarov: indentation loadУниверсальный русско-английский словарь > нагрузка на индентор
-
5 нагрузка при вдавливании
Plastics: indentation loadУниверсальный русско-английский словарь > нагрузка при вдавливании
-
6 наноиндентирование
Mechanics: depth sensing testing (см. nanoindentation), ultra-low-load indentation (см. nanoindentation), instrumented indentation (см. nanoindentation), nanoindentation (совокупность методов, использующих прецизионное локальное силовое воздействие на материал и одновременную регистрацию деформационных откликов с нанометровым разрешением)Универсальный русско-английский словарь > наноиндентирование
-
7 след
trace
- (от колес на земле) — tire footprint
-, аэродинамический — aerodynamic trail
аэродинамический след, образующийся у законцовок крыла, воздушных винтов и др. точек ла максимального падения давления. — aerodynamic trails form off the tips of wings and propellers and other points of maximum pressure decrease.
- износа — sign of wear
-, инверсионный — condensation /vapor/ trail
белая облачная полоса за самолетом, летящим на большой высоте, от выхлопных газов, содержащих водяной пар. — а visible trail of condensed water vapor or ice particles left behind an aircraft.
- истирания — sign of scuffing
-, конденсационный — condensation trail
- коррозии — trace(s) of corrosion
- короткого замыкания — evidence of shorting
- контакта зубьев шестерен (на зубьях др. шестерни) — gear tooth (contact) marking
- масла — oil trace
- нагара — trace of carbon deposit
- надира — sign of scoring
- от шарика (на обойме подшипника) — ball indentation
- повреждения — evidence of damage
- подгара — sign /trace/ of burn(s)
форма и расположение с. контакта зубьев шестерни (без нагрузки) — (nо-load) tooth contact pattern
иметь с. задиров — show /bear/ signs of scoring
удалять с. (нагара) — remove traces (or carbon)Русско-английский сборник авиационно-технических терминов > след
См. также в других словарях:
Indentation hardness — tests are used to determine the hardness of a material to deformation. Several such tests exist, wherein the examined material is indented until an impression is formed; these tests can be performed on a macroscopic or microscopic scale. When… … Wikipedia
ILD — may mean:*Incremental Link Editor, incremental version of ld(Unix) utility. *Indentation Load Deflection *Institute for Liberty and Democracy *Inter Layer Dielectric, a kind of Dielectrics that is used in semiconductors served as an insulator to… … Wikipedia
Nanoindentation — is a variety of indentation hardness tests applied to small volumes. Indentation is perhaps the most commonly applied means of testing the mechanical properties of materials. The nanoindentation technique was developed in the mid 1970s to measure … Wikipedia
Contact mechanics — Continuum mechanics … Wikipedia
solids, mechanics of — ▪ physics Introduction science concerned with the stressing (stress), deformation (deformation and flow), and failure of solid materials and structures. What, then, is a solid? Any material, fluid or solid, can support normal forces.… … Universalium
YAML — (IPAEng|ˈjæməl, rhymes with camel ) is a human readable data serialization format that takes concepts from languages such as XML, C, Python, Perl, as well as the format for electronic mail as specified by RFC [http://www.rfc… … Wikipedia
Ceramography — is the art and science of preparation, examination and evaluation of ceramic microstructures.[1] Ceramography can be thought of as the metallography of ceramics. The microstructure is the structure level of approximately 0.1 to 100 µm, between… … Wikipedia
Rockwell scale — The Rockwell scale is a hardness scale based on the indentation hardness of a material. The Rockwell test determines the hardness by measuring the depth of penetration of an indenter under a large load compared to the penetration made by a… … Wikipedia
Vickers hardness test — A Vickers hardness tester The Vickers hardness test was developed in 1924 by Smith and Sandland at Vickers Ltd as an alternative to the Brinell method to measure the hardness of materials.[1] The Vickers test is often easier to use than other… … Wikipedia
Hardness — This article is about mechanical properties of materials. For other uses, see Hard. Hardness is the measure of how resistant solid matter is to various kinds of permanent shape change when a force is applied. Macroscopic hardness is generally… … Wikipedia
Nanoindenter — A nanoindenter A nanoindenter is the main component for indentation hardness tests used in nanoindentation. Since the mid 1970’s nanoindentation has become the primary method for measuring and testing very small volumes of mechanical properties.… … Wikipedia